Alrashid Cyber Mall, is Designed and hosted by Nova Stars Informations Services, Memeber of The Saudi Network, Trade and business informations and links to Saudi Arabia, Arabian gulf and middle east area.

Quran, Arabic and English
Nova Stars Elecronics

 
Saudi Arabia, Trade and business informations and links to Saudi Arabia, Arabian gulf and middle east area.
Member of
The Saudi Network, Trade and business informations and links to Saudi Arabia, Arabian gulf and middle east area.
Saudi Arabia Trade and Business Directory
Nova Stars Information Services, Trade and business informations and links to Saudi arabia, arabian gulf and middle east area.
Special Communication Systems
Home Table of Content Search Company Profile Online Shopping

Cables Terminology

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish.

 

 

Cable & Wire Terminology

A|B|C|D|E|F|G|H|I|J|K|L|M|N|O|P|Q|R|S|T|U|V|W|X|Y|Z 

[A] 
AAR -American Association of Railroads 

Abrasion Resistance -Ability of a wire, cable or material to resist surface wear. 

Accelerated Life Test -An accelerated life test is a test in which certain factors such as 
voltage, temperature, etc. to which a cable is subjected are increased in magnitude 
above normal operating values to obtain observable deterioration in a reasonable period 
of time and thereby afford some measure of the probable cable life under operating 
voltage, temperature, etc. 

Accelerator -A chemical additive which hastens a chemical reaction under specific 
conditions. A.C. Resistance -The total resistance offered by a device in an alternating 

resistance. 

Activator - A chemical additive used to initiate the chemical reaction in a specific 

current circuit due to inductive and capacitive effects, as well as the direct current 

chemical mixture 

Active Current -In an alternating current, a component in phase with the voltage; the 
working component as distinguished from the idle or wattles component. 

Active Pressure -In an A.C. circuit, the pressure which produces a current, as 
distinguished from the voltage impressed upon the circuit. 

Admittance - The measure of the ease with which an alternating current flows in a 
circuit. The reciprocal of impedance. 

Adhesion -The state in which two surfaces are held together by interfacial forces which 
may be chemical or mechanical in nature. 

Aging - The irreversible change in properties or appearance of a material with time and 
under specific conditions (usually accelerated representations of environmental states, 
such as high temperature, oxygen or other carious conditions). 

 



Alloy - A metal formed by combining two or more different metals to obtain desirable 
properties. 

Alternating Current (AC) -Electric current that continually reverses its direction; it is 
expressed in cycles per second (hertz or Hz). 

Alternating Voltage - The voltage developed across a resistance or impedance 
through which alternating current is flowing. 

Ambient Temperature - Any all encompassing temperature within a given area 

Ampacity -The maximum current an insulated wire or cable can safely carry without 
exceeding either the insulation or jacket material limitations (Same as Current Carrying 
Ampacity). 

Ampere -The unit of current. One ampere is the current flowing through one ohm of 
resistance at one volt potential 

Ampere's Law -The magnetic intensity at any point near a current carrying conductor 
can be computed on the assumption that each infinitesimal length of the conductor 
produces at the point of an infinitesimal magnetic density The resulting magnetic 
intensity at the point is the vector sum of the contributions of all the elements of the 
conductor. 

Anneal - Relief of mechanical stress through heat and gradual cooling Annealing 
copper renders it less brittle. 

Annular Conductor -A number of wires stranded in three reversed concentric layers 
around a core 

Anode - The electrode through which a direct current enters the liquid gas or other 
discrete part of an electrical circuit the positively charged pole of an electrochemical 
cell. 

ANSI -The American National Standards Institute 

Anti-Oxidant - A substance which prevents or slows down oxygen decomposition 
(oxidation) or a material exposed to air. 



Anti Ozonant - A substance which prevents or slows down material degeneration due 


to ozone reaction. 
Arc - 1.) A Luminous glow formed by the flow of electric current through ionized air, gas 
or vapor between separated electrodes or contacts. 2) A portion of the circumference of 
a circle. 


Arc Over Voltage -The minimum voltage required to create an arc between electrodes 


separated by gas or liquid insulation under specified conditions. 
Area of conductor - The size of a conductor cross-section, measured in circular mils 
square inches, etc. 


Armor - A braid or wrapping of metal, usually steel, used for mechanical protection. 
Generally placed over the other sheath. 
ASA - The American Standards Association. Former names of ANSI. 
ASME - The American Society of Mechanical Engineers. 
ASP -Aluminum Steel Polyethylene. Provides mechanical and electrical protection. 


ASTM - The American Society for Testing and Materials 
Attenuation - Power loss in an electrical system. In cables, generally expressed on dt 
per unit length, usually 1000ft. 


Audio Frequency - Frequencies within the range of human hearing (approximately 20 


Hz to 20 kHz). 
AWG -American Wire Gage. A wire diameter specification. The smaller the AWG 
number, the larger the wire diameter. 


……………………………………………………………………………………………… 




[B] 
Balanced Credit -A circuit so arranged that the impressed voltages on each conductor 
of the pair are equal in magnitude but opposite in polarity with respect to ground. 

Balium - A device for matching an unbalanced coaxial transmission line to a balanced 
two-view system. 

Band Marking - A continuous circumferential band applied to a conductor at regular 
intervals for identification. 

Band Width -The difference between the upper and lower limits of a given band of 
frequencies. It is expressed in hertz. The range of frequencies that a transmitted 
communications signal occupies or that a receiving system can accept. For example, it 
takes more bandwidth to download a photograph in a second than to download a page 
of text. Virtual reality and three-dimensional audio/visual presentations require even 
more. 

Bare Conductor -A conductor having no covering. A conductor with no coating or 
cladding on the copper. 

Binder -A tape or thread used for holding assembled cable components in place. 

Blown jacket -Outer cable covering applied by controlled inflation of the cured jacket 
tube then pilling the cable through it. 

Bond -An attachment at and interface between an adhesive and an adherent or 
between materials attached together. 

Bond Strength -Amount of adhesion between surfaces, e.g., in bonded ribbon cable. 

Booster -An amplifier inserted into a cable to increase the signal amplitude in order to 
compensate for signal loss due to attenuation. This extends the transmission range of 
the cable. Transformers may be employed to boost ac voltages. The term booster is 
also applied to amplifiers used in television receiving antenna systems. 

Boot -A protective covering over any portion of a cable or conductor in additions to its 
jacket or insulations. 



Braid -A group of textile or metallic filaments interwoven to form a tubular flexible 
structure which may be applied over one or more wires, or flattened to form a strap. 

Braid Angle -The angle between a strand of wire in a braid shield and the longitudinal 
axis (i.e. axis along the length of the center) of the cable it is wound around. 

Braid Carrier - A spool or bobbin on a braider which holds on group or strands or 
filaments consisting of a specific number of ends. The carrier revolves during braiding 
operations. 

Brand Ends - The number of strands used to make up one carrier. The strands are 
wound side by side on the carrier bobbin and lie parallel in the finished braid. 

Brazing -The joining of ends of two wires, rods or groups of wires with a nonferrous 
filler metal at temperature above 800F (427C). 

Breakdown (Puncture) - A disruptive discharge though the insulation. 

Breakdown of Insulation -Failure of an insulation resulting in a flow if current through 
the insulation. It may be caused by the application of too high voltage or by defects or 
decay. 

Breakdown Voltage - The voltage at which the insulation between two conductors will 
fail and allow electricity to conduct or 'arc'. 

Breakout - The point at which a conductor or conductors are separated from a multiconductor 
cable to complete circuits at various points along the main cable. 

Building Wire -ire used for light power 600 Volts or less, usually not exposed to 
outdoor environment. 

Bunch Stranding - Conductors twisted together with the same lay and direction without 
regard to geometric pattern. 

Bundle (fiber optic) - A number of fibers grouped together, usually carrying a common 
signal. 

Buried Cable -A cable installed directly in the earth without use of underground 
conduit. Also called "direct buried cable". 



Bus -Wire used to connect two terminals inside of and electrical unit. 
Butt -joining of two conductors end to end, with no overlap and with the axes in line. 
Butt Splice -A splice wherein two wires from the opposite ends butt against each 


other, or against a stop, in the center of a splice. 
Butt Wrap -Tape wrapped around an object or conductor in a edge-to-edge condition. 
Byte -A group of eight adjacent binary digits (8 bits). 
………………………………………………………………………………………………… 




[ C] 
Cable -A group of individually insulated conductors or subcomponents twisted helically. 

Cable Assembly - A completed cable and its associated hardware ready to install. 

Cable Filter - The material used in multiple conductor cable to occupy the spaced 
forced by the assembly of components, thus forming a core of the desired shape 
(normally cylindrical). 

Cabling -The grouping or twisting together of two or more insulated conductors or 
subcomponents to form 
a cable. 

Cabling Factor - Used in the formula for calculating the diameter of and unshielded, 
unjacketed cable. D-Kd, where D is the cable diameter, K is the factor and d is the 
diameter of one insulated conductor. 

Caged Armor -A construction using wires within a jacket to increase mechanical 
protection and tensile strength. This construction is sometimes used in submarine 
cables. 

Capacitance -Storage of electrically separated charges between two plates having 
different potentials. The value depends largely on the surface area of the plates and the 
distance between them. 

Capacitance Direct -The capacitance measured directly from conductor to conductor 
through a single insulating layer. 

Capacitance Mutual -The capacitance between two conductors with all other 
conductors including shield, sort circuited to ground. 

Capacitance, Unbalanced to ground - An inequality of capacitance between the wires 
of two or more pairs which result in a transfer of unwanted signal from one pair to 
others. 

Capacitive Coupling - Electrical interaction between two conductors caused by the 
capacitance between them. 



Carrier -The basic woven grouping of a braided shield consisting of one or several 
parallel ends 

Cathode - Negative pole of an electric source 

Cathodic Protection -The control of the electrolytic corrosion of an underground or 
underwater metallic structure by the application of an electric current through a 
sacrificial anode in such a way that the structure is made to act as a cathode of an 
electrolytic cell. 

Cellular Polyethylene - Expanded or "foam" polyethylene consisting of individual 
closed cells suspended in a polyethylene medium. 

Center to Center - Distance See Pitch 

Certificate of Compliance (C of C) - A certificate which shows that the product being 
shipped meets customer's specifications. 

Certified Test Report (CTR) - A report providing actual test data on a cable. Tests are 
normally run by a Quality Control Department, which shows that the product being 
shipped conforms to test specifications. 

Characteristic Impedance - The impedance that, when connected to the output 
terminals of a transmission line of any length, makes the line appear infinitely long. The 
ratio of voltage to current at every point along a transmission line on which there are no 
stranding waves 

Charge - The quantity of electricity held statically in a condenser or on an insulated 
conductor. 

Charging Current -The current produced when a DC voltage is first applied to 
conductors of an un-terminated cable. It is caused by the capacitive reactance of the 
cable, and decreases exponentially with time. 

Charging Time - The time required for the voltage between two conductors of a cable 
to acquire a value equal to 98.2% of the magnitude of an instantaneously applied DC 
voltage change. 



Chlorosulfonated Polyethylene (CSPE) -A rubbery polymer made by treating 
polyethylene with chlorine and sulfur dioxide It is suitable compounded and cross linked 
for application as jacket or as insulation Manufactured by E.I. DuPont under trade name 
of Hypalon 

Circuit -The complete path through which a current flows or part of the complete path 
such as one conductor. 

Circuit Sizes - A popular term for building wire sizes 14 through 10 AWG. 

Circular Mil -The area of a circle one mil (.001") in diameter, 7.546 x 10-7 sq. in. Used 
in expressing wire cross sectional area 

Cladding - A method of applying a layer of metal over another metal whereby the 
junction of the two metals in continuously welded. 

Coat - To cover with a continuous layer of compound (such as varnish) for purposed of 

depending on the nature of the substance. 

fishing, protection, or enclosing. Usually comprises variable degrees of impregnation 

Coating -A material applied to the surface of a conductor to prevent environmental 
deterioration, facilitate soldering or improve electrical performance. 

Coaxial Cable - A cable consisting of two cylindrical conductors with a common axis, 
separated by dielectric. 

Cold Flow -Permanent deformation od the insulation due to mechanical force or 
pressure (not due to heat softening). 

Cold Test - any test to determine the performance of cables during or after subjection 
to a specified low temperature for a specified time. 

Color Test -a system for circuit identification through use of solid colors and 
contrasting tracers. 

Common Axis Cabling -in multiple cable constructions, a twisting of all conductors 
about a "common axis" with two conductor groups then selected as pairs. This practice 
yields smaller diameter contructions that does a separate axis construction, but tends to 
yield greater susceptance to EMI and ESI. 



Common Mode (Noise) - caused by a difference in "ground potential". By grounding at 
either end rather than both ends (usually grounded at source) on can reduce this 
interference. 

Compact Stranded Conductor - a unidirectional or conventional conductor 
manufactured to a specific diameter, approximately 8 to 10% below the nominal 
diameter of a non-compact conductor of the same cross sectional area. 

Compatibility -the ability of dissimilar materials to exist in mutual proximity or contract 
without changing their physical or electrical properties. 

Composite Cable -a cable consisting of two or more different types or sizes of wires. 

Compound - an insulating or jacketing materials made by mixing two or more 
ingredients. 

Concentric Stranding -a central wire surrounded by one or more layers of helically 
wound strands in a fixed round geometric arrangement. 

Concentricity - in a wore or cable, the measurement of the location of the center of the 
conductor with respect to the geometric center of the surrounding insulation. 

Conductance -the ability of a conductor to carry electric current. It is the reciprocal of 
resistance and is measure in ohms. 

Conductivity -the capability of material to carry electrical current-usually expressed as 
a percentage of copper conductivity (copper being 100%) 

Conductor -an un-insulated wire suitable for carrying electrical current. 

Conduit -a tube or trough in which insulated wired and cable are run. 

Connector - a device used to physically and electrically connect two or more 
conductors. 

Contract - the part of a connector which actually carried the electrical current, and are 
touched together or separated to control the flow. 



Continuity Check - a test to determine whether electrical current flows continuously 


throughout the length of a single wire or individual wires in a cable. 
Continuous Vulcanization -simultaneous extrusion and vulcanization of rubber-like 
wires in a cable. 


Control Cable -a multicolor cable made for operation in control or signal circuits. 
Copolymer -a polymer formed from two or more types of Monomers. 
Copper-Clad -steel with a coating of copper welded to it, as distinguished from copper-


plated. Same as Copperweld. 


Copperweld - the trade name of Felxo Wire Division (Copperweld Steel Corp.) for their 
copper-clad steel conductors. 
Cord - a small, flexible insulated cable. 
Corona - a discharge due to ionization of air around a conductor due to a potential 


gradient exceeding a certain critical value. 


Corona Effect - in wiring, the effect produced when two wires of other conductors 
having a great difference of voltage are placed near each other. 
Corona Loss -A loss or discharge which occurs when two electrodes having a great 

difference of pressure are placed near each other. 
Corona Resistance -The time that the insulation will withstand a specific level of field-


intensified ionization that does not result in the immediate complete breakdown of the 
insulation. 
Corona Test -A test to determine the ability of cable to withstand the formation of the 


corona under an increasing applied voltage and the extinguish corona when a corona-
producing voltage is reduced. 
Corrosion - The deterioration of a material by chemical reaction or galvanic action. 
CPE - jacketing compound based on chlorinated polyethylene. 




Crazing - the minute crack on the surface of plastic materials. 
CRCS - an acronym for continuous rigid cable support. Synonymous with tray. 
Creep - The dimensional change with time of a material under load. 
Creepage - Electrical leakage on a solid dielectric surface. 
Cross-linked - inter-molecular bonds between long chain thermoplastic polymers by 


chemical or electron bombardment means. The properties of the resulting thermosetting 


material are usually improved. 
Crosstalk - A type of interference caused by signals from one pair or cable being 
coupled into adjacent pairs or cables. Can occur with audio, data, or RF signals. 


C.S.A -Abbreviation for Canadian Standards Association, the Canadian version of the 
Underwriters Laboratories. 
Cure -See Vulcanization 
Curl -The degree to which a wire tends to form a circle after removal from a spool. An 
indication of the ability of the wire to be wrapped around the posts in long runs. 

Current - the rate of flow of electricity in a circuit, measured in amperes. 

Current-Carrying Capacity -the maximum current an insulated conductor or cable can 
continuously carry without exceeding its temperature rating. It is also called ampacity. 
Current Penetration -the depth a current of a given frequency will penetrate into the 

surface of a conductor carrying the current. 

Cut-Through -Resistance of solid material to penetration be an object under conditions 
of pressure, temperature, etc. 
CV (Continuous Vulcanization) - simultaneous extrusion and vulcanization of wire 

coating material. 
Cycle -The complete sequence of alteration or reversal of the flow of an alternation 
electric current. 




[ D] 
D.C. - abbreviation of "Direct Current" 
Decibel (dB) -A unit to express differenced of power level. Used to express power gain 
in amplifiers or power loss in passive circuits or cables. 

Delay Line - A transmission line or equivalent device designed to delay a wave or 
signal for a specific length of time. 

Derating Factor - A multiplier used to reduce the current carrying capacity of 
conductors in more adverse environments, such as higher temperature, or where 
multiple conductors are together in one conduit. 

Dielectric - An insulating (non-conducting) medium. It is the insulating material between 
conductors carrying a signal in a cable. In coaxial cables it is between the center 

conductors plus any surrounding air or other material. 

conductor and the outer conductor. In twisted pair cables it is the insulation between 

Dielectric Absorption -That property of an imperfect dielectric whereby there is an 
accumulation of electric charges within the body of the material when it is placed in an 
electric field. 

Dielectric Breakdown -The voltage at which a dielectric material is punctured, which is 
divisible by thickness to give dielectric strength. 

Dielectric Constant (K) - Also called relative permittivity. That property of a dielectric 
which determines the amount of electrostatic energy that can be stored by the material 
when a given voltage is applied to it. Actually, the ratio of the capacitance of a capacitor 
using the dielectric to the capacitance of an identical capacitor using a vacuum (which 
has a dielectric constant of 1) as a dielectric. A number which indicates the quality of a 
material to resist holding an electrical charge when placed between two conductors. 

Dielectric Strength - The voltage an insulation can withstand before it breaks down. 
Usually expressed as "volts per mil". 

Dielectric Test - a test in which a voltage higher than the rated voltage is applied for a 
specific time to determine the adequacy of the insulation under normal conditions. 



Direct Burial Cable - A cable installed directly in the earth. 


Direct Capacitance - The capacitance measured directly for conductor to conductor 
through a single insulation layer. 
Direct Current (DC) - An electric current which flows in only one direction. 
Direct Current Resistance. (D.C.R) - The resistance offered by any circuit to the flow 


of direct current. 


Dissipation Factor - The tangent of the loss angle of the insulating material (Also 
referred to as loss tangent, tan S and approximate power factor. 
Double Foot -Combined length of one linear foot of paired material; i.e., one double 


foot is equal to one foot of positive material plus one foot of negative material. Usually 


used in determining thermocouple wire loop resistance. 
Drain Wire - In a cable, the un-insulated wire in intimate contact with a shield to provide 
for easier termination of such a shield to a ground point. 


Drawing - In wire manufacturing, pulling the metal through a die or series of dies to 
reduce diameter to a specified size. 
Drum Packed - The method of coiling wire into fiber drums for shipment. 


Duct - An underground or overhead tube for carrying electrical conductors. 
Duplex Insulated - In the thermocouple industry, a combination of dissimilar metal 
conductor of a thermocouple or thermocouple extension wire. 


………………………………………………………………………………………………… 




[ E] 
Eccentricity - Like concentricity a measure of the center of a conductor's location with 
respect to the circular cross section of the insulation. Expressed as a percentage of 
displacement of one circle within the other. 
ECTFE - Ethylene chloro - trifluoroethylene (Halar) 
EIA - Abbreviation for Electronic Industries Association 
Elastomer - A rubber like substance 
Electromagnetic - Pertaining to the combined electric and magnetic fields associated 
with movements of electrons through conductors 
Electromotive Force (e.m.f.) -Pressure or voltage. The force which causes current to 
flow in a circuit. 
Electrostatic -Pertaining to static electricity or electricity at rest. A constant intensity 
electric charge. 
Elongation - The fractional increase in length of a material stressed in tension. 
Embossing -a marker identification by means of thermal indentation leaving raised 
lettering on the sheath material of cable. 
Emergency Overload - load which occurs when larger than normal currents are carried 
through a cable or wire over a certain period of time. 
EMI - abbreviation for Electromagnetic Interference. 
Energize -to apply rated voltage to a circuit or device in order to activate it. 
Equilay -more than one layer of helically laid wire with the direction of lay reversed for 
successive layers, both with the length of lay the same for each layer. 
Etched Wire -a process applied to fluroplastic wire in which the wire is passed through 
a sodium bath to create a rough surface to allow epoxy resin to bond the fluroplastic. 



ETFE -Ethylene tetrafluoroethylene (Teflon) 

Ethylene Propylene Rubber (EPR) - an ozone resistance rubber consisting primarily of 
ethylene propylene copolymer (EPM) or ethylene propylene diene terpolymer (EPDM). 

ETPC - abbreviation for electrolytic tough pitch copper. It has a minimum conductivity of 
99.9% 

External interference - the effects of electrical waves or fields which cause sounds 
other than the desired signal (static). 

Extrusion -the process of continuously forcing both a plastic or elastomer and a 
conductor core through a die, thereby applying a continuous coating of insulation or 
jacket to the core or conductor. 

…………………………………………………………………………………………………… 



[ F] 
Fatigue Resistance - resistance to metal crystallization which leads to conductress or 
wires breaking from flexing. 

FEP -fluorinated Ethylene Propylene is a "Teflon" fluorocarbon resin and is a registerd 
trademark of the DuPont Compnay. This is a melt extrudable fluorocarbon resin. 

Fiber - A single, separate optical transmission element characterized by core and 
cladding. 

Fiber Dispersion -(fiber optic) pulse spreading in a fiber cause by differing transit 
times of various modes. 

Fiber Optics - Light transmission through optical fibers for communication and 
signaling. A technology that transmits information as light pulses along a glass or plastic 
fiber. Optical fiber carries much more information than conventional copper wire and is 

optical fiber. 

generally not subject to interference. Most telephone company long-distance lines are 
Field -An area through which electric and/or magnetic lines of force pass. 

Filled Cable -a telephone cable construction in which the cable core is filled with a 
material that will prevent moisture from entering or passing through the cable. 

Filler - Nonconducting components cabled with the insulated conductors or optical 
fibers to impart roundness, flexibility, tensile strength, or a combination of all three, to 
the cable. 

Film - a thin plastic sheet. 

Flame Resistant - The ability of a material not to fuel a flame once the source of heat is 
removed. 

Flammability -the measure of the material ability to support combustions. 

Flammability Test -A test to determine the ability of a cable to resist ignition when 
placed neat a source of heat of flame and to self-extinguish when removed from this 
source. 



Flat braid -a woven braid of tinned copper strands rolled flat at time of manufacture to 
a specified time. 

Flat Cable -a cable with two smooth or corrugated but essentially flat surfaces. 
Flat Conductor -a wire having a rectangular cross section as opposed to round or 
square conductors. 


Flat Conductor Cable - a cable with a plurality of flat conductors. 


Flex Life -the measurement of the ability of a conductor or cable to withstand repeated 
bending. 
Flexible -the quality of a cable or cable component which allows for bending under the 


influence of outside force, as opposed to limpness which is bending due to the cable's 


own weight. 
Flexibility -The ability of a cable to bend in a short radius. The ability of a cable to lay 
flat or conform to a surface as with microphone cables. 


Floating -Referring to a circuit which has no connection to ground. 
Foamed Plastic - insulations having a cellular structure. 
FR-1 -a flammability rating established by Underwrites Laboratories for wires and 


cables that pass a specially designed vertical flame test. The designation has been 


replaced by VW-1. 
Frequency - The number of times a periodic action occurs in one second. Measured in 
Hertz. 


Fuse Wire -Wire made from alloy that melts at a relatively low temperature. 


Fused Spiral Tape -a PTFE Insulated hookup wire. The spiral wrapped conductor is 
passed through a sintering oven where overlaps are fused together. 
……………………………………………………………………………………………………. 




[G] 
Galvanometer -an instrument used for detecting or measuring small electrical current. 
Gas Filled Cable -a self-contained pressure cable in which the pressure medium is an 
inert gas having access to the insulation. 
Gauge -a term used to denote the physical size of a wire 
Giga -a numerical prefix denoting one billion. 
Ground - a conducting connection between an electrical circuit and the earth or other 
large conductions body to serve as an earth thus makes a complete electrical circuit. 
…………………………………………………………………………………………………… 



[H] 
Halar -a trade name of Allied Chemical for their copolymer of ethylene and 
chlorotriflurorethylene. Abbreviation ECTFE 

Hard Drawn Copper Wire -Copper wire that has not been annealed after drawing. 

Harness -an arrangement of wires and cables, usually with many breakouts, which 
have been pulled together or pulled into a rubber or plastic sheath, used to interconnect 
an electric circuit. 

Hash Mark Stripe - a non-continuous helical stripe applied to a conductor for 
identification. 

Heat Distortion -Distortion or flow od a material of configuration due to application of 
heat. 

Heat Endurance 


specific physical or electrical test. 
the time of heart aging that a material can withstand before failing a 

Heat Resistance -ability of a substance to maintain physical and chemical identity and 
electrical integrity under specified temperature conditions. 

Heat Seal -a method for sealing by thermal fusion. 
Heat Shock - a test to determine stability of a material by sudden exposure to a high 
temperature for a short period of time. 


Helical Stripe - a continuous, colored spiral stripe applied to a conductor for circuit 


identification. 
Henry - Unit of inductance such that the induced voltage in volts is numerical equal to 
the rate of change in current in amperes per second. 


Hermetically Sealed -a gaslight enclosure that has been completely sealed by fusion 
or other comparable means. 
Hertz (Hz) -a term replaced cycles-per-second as a unit of frequency. 




Hi Pot - a test designed to determine the highest voltage that can be applied to a 
conductor without electrically breaking down the insulation. 

High Voltage -generally, a wire or cable with an operating voltage of over 35,000 volts. 
Hook-up Wire - a single insulated conductor used for low current, low voltage (usually 
under 600 volts) applications within enclosed electronic equipment. 

Hot Tin Dip - a process of passing bare wire through a bath of molten tin to provide a 
coating. 

Hygroscopic - capable of absorbing and retaining moisture. 
Hypalon -DuPont's trade name for their chlorosulfonated polyethylene, an ozone 
resistant synthetic rubber. 


Hz - Abbreviation for Hertz. 
…………………………………………………………………………………………………… 



[I] 
IEC - International Electrotechnical Commission, similar to the ISO in structure and 
scope. 
IEEE -Institute of Electrical and Electronics Engineers. 
Impendence -The total opposition that a circuit offers to the flow of alternating current 
or any other varying current at a particular frequency. 
IMSA -International Municipal Signal Association Specifications for Fire Alarm Cable. 
Induced Current -an electrical current set up in a circuit by butting line of force; a 
current caused by electromagnetic induction. 
Inductance -The property of wire which stores electrical current in a magnetic field 
around the wire. By coiling wire, the effect can be intensified. It is measured in Henrys. 
Inductive Coupling -crosstalk resulting form the action of the electromagnetic field of 
one conductor on the other. 
Insulation - A material having good dielectric properties which is used to separate close 
electrical components, such as cable conductors and circuit components. 
Insulation Level 100% - Cable for use on grounded systems or where the system is 
provided with relay protection such that ground faults will be cleared as rapidly as 
possible but in any case within one minute. 
Insulation Level 133% - Cable for use on grounded systems or where the faulted 
section will be de-energized in a time not exceeding one hour. 
Insulation Resistance ( I.R.) - That resistance offered by and insulation to an 
impressed DC voltage, tending to produce a leakage current through the insulation. 
Insulation Thickness - The wall thickness of the applied insulation. 
Interconnecting Cable -the wiring between modules, between units, or the larger 
portions of a system. 



Interference -and undesired electrical signal induced into a conductor by electrical or 


electromagnetic means. 
Interstices - voids or valleys between individual strands in a conductor by electrical or 
electromagnetic means. 


Ionization -The formation of ions. Ions are produced when polar compounds are 
dissolved in a solvent and when a liquid, gas, or solid is caused to lose or gain electrons 
due to the passage of an electric current. 

ISA -Instrument Society of America 
ISO - International Standards Organization 
……………………………………………………………………………………………………… 



[J] 
Jacket -Pertaining to wire and cable, the outer protective covering that may also 
provide additional insulation. 
JAN Specification -Joint Army-Navy specifications (forerunner of present Military 
Specification). 
Jumper Cable -a short flat cable interconnecting two wiring boards or devices 
………………………………………………………………………………………………….. 



[K] 
Kilo -A numerical prefix denoting 1000. 
KV - Kilovolt (1000 volts) 
KVA -Kilovolt ampere. 
KW -Kilowatt. 
Kynar - Penwalt trade name for polyvinylidene flouoride. Typically used as insulation for 
wire wrap wire. 
…………………………………………………………………………………………………… 



[L] 
Lacquer -a liquid resin or compound applied to textile braid to prevent fraying, moisture 
absorption, etc. 

Laminated Tape - a tape consisting of two or more layers of different materials bonded 
together. 

LANCE - Local Area Network for Controller Ethernet 

LANS -Local Area Networks System (integration of computer and communication). 
System that wires together all computers and peripherals in an office so they can talk to 
each other. 

Lay - The length measured along the axis of a wire or cable required for a single strand 
(in stranded wire) or conductor (in cable) to make one complete turn about the axis of 
the conductor or cable. In a twisted pair cable, the lay length is the distance it takes for 
the two wires to completely twist around each other. 

Lay Direction - the twist on the cable as indicated by the top strands whole looking 
along the axis of the cable away from the observer. Described as "right hand" or "left 
hand". 

Leaching and Non-Leaching -in a leaching wire the plasticizer will migrate when 
exposed to heat. A non-leaching wire will retain its plasticizer under extreme 
temperature conditions and remain flexible after baking. 

Leakage Current - the undesirable flow of current through or over the surfaces of an 
insulation. 

Life Cycle - a test to determine the length of time before failure in a controlled, usually 
accelerated, environment. 

Limits of Error - the maximum deviation (in degrees or percents) of a thermocouple or 
thermocouple extension wire from standard emf-temperature to be measured. 

LOCA -abbreviation for Loss of Coolant Accident, a system malfunction associated 
with nuclear generation stations. 



Local Area Network - a baseband or broadband interactive bi-directional 

communication system for information exchange on a common transmission line. 
Longitudinal Shield - a tape shield, flat or corrugated, applied longitudinally with the 
axis of the core being shielded. 

Longitudinal Wrap -tape applied longitudinally with the axis of the core being shielded. 

Loop Resistance - the total resistance of two conductors measured round tip from one 
end. 
Loss Factor -the product of the dissipation and dielectric constant of an insulation 

material. 
Low Noise Cable - cable configuration specifically constructed to eliminate spurious 


electrical disturbances caused by capacitance changes of self-generated noise induced 
by either physical abuse or adjacent circuitry. 
Low Loss Dielectric -an insulation material that has a relatively low dielectric loss, 


such as polyethylene or Teflon. 
Low Tension -low voltage, as applied to ignition cable. 
…………………………………………………………………………………………………… 




[M] 
Magnetic Field - the region within which a body or current experiences magnetic 
forces. 
Magnetic Flux - the rate of flow of magnetic energy across or through a surface (real or 
imaginary). 
Magnetic Noise - caused my change in current level, e.g., AC powerline (created 
magnetic field around that cable) this magnetic field causes the magnetic noise. 
MC Metal-Clad Cable -NEC type designation for power and control cables enclosed in 
a smooth metallic sheath, welded and corrugated metallic sheath, or an interlocking 
taper armor. 
MCM - one thousand circular mils. 
Megarad - a unit for measuring radiation dosage, Equal to one million rads. 
Megohm -one million ohms. 
Member -a group of insulated wires to be cabled with other stranded groups into 
multiple-membered cable. 
Messenger- the linear supporting member, usually a high strength steel wire, used as 
the supporting element of a suspended aerial cable. The messenger may be an integral 
part of the cable, or exterior to it. 
Mho - the unit of conductivity. The reciprocal of an ohm. 
Muticonductor - more than one conductor within a single cable complex. 
Mutual Capacitance - capacitance between two conductors when all other conductors 
including ground are connected together and then regarded as an ignored ground. 
Mutual Inductance - the ratio of voltage induced on one conductor to the time tae of 
current change in the separate conductor causing this induction. 



MW -radio hookup wire with polyvinyl insulation and plain or nylon jacket, braid, or 
shield. 1000V. 
Mylar -DuPont trademark for a polyester material used in the form of a tape. 
…………………………………………………………………………………………………… 



[N] 
National Electric Code (NEC) -a consensus standard published by The National Fire 
Protection Association (NFPA) and incorporated in OSHA regulations. 
NBFU -National Bureau of Fire Underwriters. NBS - National Bureau of Standards. 
NEC - See National Electric Codes. 
NEMA - National Electrical Manufacturers Association. 
Neoprene - trade name for polychloroprene synthetic rubber, used for jacketing when 


suitable compounded. 


Noise - in a cable or circuit, any extraneous signal which tends to interfere with the 
signal normally present in or passing through the system. 
Nominal O.D. - the desired diameter for a cable that is established within a +/


tolerance. 
Non-Contaminating -type of PVC jacket material whose plasticizer will not migrate into 


the dielectric of a coaxial cable and thus avoids contaminating and destroying the 
dielectric. 
Non-Contaminating PVC - a polyvinylchloride formulation, which does not produce 


electrical contamination through plasticizer migration. 
Nylon - a group of polyamide polymer which is used for wire and cable jacketing. 
………………………………………………………………………………………………….. 




[O] 
O.D. -outside diameter. 
Off-center - conductor displaced within the cross-section of its insulation. 
Offgassing -percentage of a specified gas releases during the combustion of insulation 
or jacketing material. 
OFHC -abbreviation for oxygen-free high conductivity copper. It has no residual 


deoxidant, 99.95% minimum copper content and an average annealed conductivity of 
101% 
Ohm -The unit of electrical resistance. The value of resistance through which a 

potential difference of one volt will maintain a current of one ampere. 

Oil Aging -cable aged in an accelerated manner by placement in an oil bath and 
heated to a pre-set temperature fr a stated time. 
Oil-Filled Cable -a self-contained pressure cable in which the pressure medium is low 

viscosity oil having access to the insulation. 
Outgassing - the dissipation of gas from a dielectric evidencing decomposition. 
OVE -approval agency of West Germany; Osesterreichischer Verband fur 


Electrotechnik. 
Overall Diameter -finished diameter over wire and cable. 
Overcoat - individual strands of tin copper stranded together and then covered with a 


tin coating. 
Overlap - the amount the trailing edge laps over the leading edge of a tape wrap. 
Oxygen index -percentage of oxygen necessary to support combustion of a specified 


material. 
Ozone -a highly active form of oxygen produced by the passage of electric discharges 
or sparks through the air or oxygen. 




[P] 
Pair -two insulated wires of single circuit associated together. 

Pairing -the union of two insulated single conductors through twisting. 

Parallel Cable - two insulated conductor's side-by-side in a cable. 

Peak Voltage - the maximum instantaneous voltage. 

Percent Conductivity - conductivity of a material expressed as a percentage of that of 
copper. 

Periodicity - The uniformly spaced cable impedance variations that result in addition of 
the reflections of a signal. The distance between them is the half wavelength most 
affected. Multiples of that frequency is also affected. Even very slight variations, which 
appear over and over in a construction or installation, can have major effects on signal 
integrity because of periodicity. 

Permittivity -see dielectric constant 

Pick - distance between two adjacent crossover points of braid filaments. The 
measurement in picks per inch indicates the degree of coverage. 

Pitch -Nominal distance from center-to-center of adjacent conductors within a cable. 
When conductors are flat, pitch is usually measured from the reference edge of a 
conductor to the reference edge of the adjacent conductor. Spacing. 

Pitch Diameter -diameter of a circle passing through the center of the conductors in 
any layer of multiconductor cable. 

Planetary Cabler -a cabler of laying down any number of shielded, over braided or 
jacketed singles, pairs, called groups or any combination of them in a sequence. 

Planetary Twister -a twisting machine whose payoff spools are mounted in rotating 
cradles that hold the axis of the spool in a fixed direction as the spools are revolved so 
the wire will not kink as it is twisted. 



Plastic Deformation - change in dimensions under the load that is not recovered when 
the load is removed. 

Plasticizer -a chemical agent added to plastics to make them softer and more pliable. 

Plenum -A compartment or chamber to which one or more air ducts are connected and 
that forms part of the air distribution system. A description for a cable that passes the 
UL 910 CMP flame test requirements. 

Plenum Cable - cable approved by Underwriters Laboratories for installation in 
plenums without the need for conduit. 

PLTC -NEC type designation for Power-Limited Tray Cable for use in class 2 or 3 
Power-Limited circuits; instrumentation supervisory control, and thermocouple 
extension. 

Polyester -Polyethylene terephthalate which is used extensively in the production of a 
high strength moisture resistant film used as a cable core wrap. 

Polythylene -A thermoplastic material having excellent electrical properties. Low 
dielectric constant, a stable dielectric constant over all frequencies, very high insulation 
resistance. In terms of flexibility, polyethylene can be rated stiff to very hard, depending 
on molecular weight and density -low density being the most flexible and the high-
density, high-molecular weight formulation being very hard. Moisture resistance is rated 
excellent. 

Polymer -A substance made of many repeating chemical units or molecules. The term 
polymer is often used in place of plastic, rubber, or elastomer. 

Polyolefin -Any of the polymers and copolymers of the ethylene family of 
hydrocarbons, such as polyethylene and polypropylene. 

Polypyopylene -A thermoplastic similar to polyethylene but stiffer and having a higher 
softening point (temperature). This material is primarily used as an insulation material. 
Typically, it is harder than polyethylene. This makes it suitable for thin wall insulations. 
The dielectric constant is 2.25 for solid and 1.55 for cellular designs. 

Polyvinyl Chloride (PVC) - A general purpose thermoplastic used for wire and cable 
insulation and jackets. 



Porosity -multiple air voids in an insulation jacket wall. 
Power Factor -the ratio of resistance to impedance. The ratio of the actual power of an 


alternating current to apparent power. Mathematically, the cosine of an angle between 
the voltage applied and the current resulting. 
PPE -Portable Power Elastomer. Same as Type W except is a thermoplastic elastomer 

insulation and jacket whereas Type W is all thermoset. 
Pre-Bond - stranded wire which has been fused, topcoat tinned, or overcoat tinned. 
Primary Insulation - the first layer of nonconductive material applied over a conductor, 


whose prime function is to act as electrical insulation. 


Progpagation Delay -Time required for a signal to pass from the input to the output of 
a device. 
Propagation Time - time required for a signal to pass from the input to the output of a 

device. 
PTFE -abbreviation for Polytetrafluoroethylene. 
Pulse -A current or voltage which changes abruptly from one value to another and 


back to the original value in a finite length of time. Used to describe one particular 


variation in a series of wave motions. 
Pulse Cable - a type of coaxial cable constructed to transmit repeated high voltage 
pulses without degradation. 


PVD - Polyvinylidene fluoride (Kynar). 
Pyrometer - see thermocouple thermometer. 
……………………………………………………………………………………………………. 




[Q] 
Quad -a four conductor cable. 
Quadders - three-bay machines which can twist four wires together and cable braided 
and shielded wires with varying lay lengths. 
QPL - Qualified parts list. 
……………………………………………………………………………………………………. 




[R] 
Rad - the unit of radiation dose which is absorbed, equal to 100 ergs/gram. 

Rated Temperature -The maximum temperature at which an electric component can 
operate for extended periods without loss of its basic properties. 

Rated Voltage - The maximum voltage at which an electric component can operate for 
extended periods without undue degradation or safety hazard. 

Reactance -A measure of the combined effects of capacitance and inductance on an 
alternating current. The amount of such opposition varies with the frequency of the 
current. The reactance of a capacitor decreases with an increase in frequency; the 
opposite occurs with an inductance. 

Reference Junction - the junction of a thermocouple which is as a known reference 
temperature. Also known as the "cold" junction,. It is usually located at the emf 
measuring device. 

Reflection Loss - The part of a signal which is lost due to reflection of power at a line 
discontinuity. 

Registration - Alignment of one object with relation to another. In flat cables it involves 
aligning conductors with contacts or solder pads. Also called register. 

Resin -an organic substance of natural or synthetic origin characterized by being 
polymeric in structure and predominantly amorphous. Most resins, through not all, are of 
high molecular weight and consist of long chain or network molecular structure. 

Resistance -In dc circuits, the opposition a material offers to current flow, measured in 
ohms. In ac circuits, resistance is the real component of impedance, and may be higher 
than the value measured at dc. 

Retractile Cable -a cable that returns by its own stored energy from an extended 
condition to it original contracted form. 

RFI - Radio Frequency Interference. 



RG/U -RG is the abbreviation for radio guide, a military designation for a coaxial cable, 


and U stands for universal. 
Ribbon Cable -A flat cable made with parallel round conductors in the same plane. 
Also referred to as planar and/or flat cable. Any cable with two or more parallel 
conductors in the same plane encapsulated by insulating material. 


Ridge maker -one or more ridges running laterally along the outer surface of the 


plastic insulated wire for purposes of identification. 
Ringing Out - The process of locating or identifying specific conductor paths by means 
of passing a current through selected conductors. 


Rise Time - the time required for the initially zero potential existing on a transmission 
line (which is terminated in its characteristics impendence) to change from 10% to 90% 
of its full DC value after a DC potential source is instantaneously applied. 


RMS or rms - Root-mean-square. 


Rockwell Harness - a test for determining hardness in which a hardened steel ball or 
diamond point is pressed into the material under test. 
Roentgen - the amount of radiation that will produce on electrostatic unit of ion per 


cubic centimeter volume. 


Rope Lay Conductor -a conductor composed of a central core surrounded by one or 
more layers of helically laid groups of wire. 
Rope Strand -A conductor composed of groups of twisted strands. 
Round Conductor - a conductor whose cross section is substantially circular. 
Rulan - DuPont's trade name for their flame-retardant polyethylene insulating material. 
Rupture - in the breaking strength or tensile strength tests, the point at which the 


material physically comes apart, as opposed to elongation, yield strength, etc. 
…………………………………………………………………………………………………… 




[S] 
SAE -Society of Automotive Engineers. 

SBR -A copolymer of styrene and butadiene. Also GR-S or Buna-S. Most commonly 
used type of synthetic rubber. 

SDN - small diameter multi-conductor control cable with a neoprene jacket and nylon 
sheath over polyethylene insulation. 

Secondary insulation -a high resistance dielectric material which is placed over 
primary insulation to protect it from absorption. 

Self Extinguishing - The characteristic of a material that extinguishes its own flame 
after the igniting flame is removed. 

Self-Supporting Cable - any assemblage of conductors which incorporates a steel 
rope of steel sheath for added tensile strength, thus enabling it to be suspended 
between widely spaced supports. 

Semi-Conducting Tape - a tape of such resistance that when applied between two 
elements of a cable, the adjacent surfaces of the two elements will maintain 
substantially the same potential. 

Semiconductor - In wire industry terminology, a material possessing electrical 
conductivity that falls somewhere between that of conductors and insulators. Usually 
made by adding carbon particles to an insulator. Not the same as semiconductor 
materials such as silicon, germanium, etc. Used for making transistors and diodes. 

Semi-Rigid PVC - a hard semi-flexible polyvinylchloride compound with low plasticizer 
content. 

SEMKO - approval agency for Sweden . 

Separator -a layer of insulating material such as textile, paper, polyester, etc. Used to 
improve stripping qualities, flexibility, mechanical or electrical protection to the 
components. 



Serve - a filament or group of filaments such as fibers or wires, wound around a central 


core. 
Served Wire Armor -spiral wrap of soft galvanized steel wires wrapped around a cable 
to afford mechanical protection and increase the cable pulling tension characteristics. 


SEW, SEWF - Silicone Rubber insulated equipment wire (CSA). 
SF -Silicone rubber insulated fixture wire, solid or 7 strand conductors, 200C. 
SFF -same as SF, except flexible stranding, 150C. 
Sheath -the outer covering or jacket of a multi-conductor cable. 
SHD-GC - portable mine power cable, three or four individually shielded conductors, 


with grounding conductors, 500V. 
Shield -A tape, serve or braid (usually copper, aluminum, or other conductive material) 


placed around or between electric circuits or cables or their components, to prevent 
signal leakage or interference. 
Shield Coverage - The optical percentage of a cable actually covered by shielding 

material. 
Shield Effectiveness - The relative ability of a shield to screen out undesirable 


interference or prevent signal leakage out of the cable. Frequently confused with the 
term shield coverage. 
Shield Percentage - The percentage of physical area of a circuit or cable actually 


covered by shielding material. 


Shock Test -a test to determine the ability of a cable to withstand a violent physical 
concussion such as might occur during handling or use. 
Shore Hardness - an instrument measure of the surface hardness of an insulating or 


jacket material. 
Signal -Any visible or audible indication which can convey information. Also, the 
information conveyed through a communication system. 




Signal Cable -a cable designed to carry current of the usually less than one ampere 
per conductor. 

Sintering - fusion of a spirally applied tape wrap jacket by the use of high heat to a 
homogeneous continuum. Usually employed for fluorocarbon, non-extrudable materials. 

SIS -indicated single conductor having synthetic thermosetting insulation of heat-
resistant, moisture-resistant, flame retarding grade. Also made with chemically cross 
linked polyethylene insulation. Used for switchboard wiring only, 90C. 

Skin Effect - The tendency of alternating current to travel only on the surface of a 
conductor as its frequency increases. 

SNM - a cable designed for the use in hazardous locations consisting of insulated 
conductors in an extruded nonmetallic jacket which is then covered with an overlapping 
spiral metal tape and wire shield and jacketed with an extruded moisture flame, oil, 
corrosion, fungus and sunlight resistant nonmetallic material. 

SO - hard service cord, same construction as type S except oil-resistant neoprene 
jacket. 600V, 60C, and 90C. 

Solid Conductor -a single unit not divided into parts. 

SOW -water resistant neoprene jacketed portable cord (CSA). 

SOW-A/SOW - service cord with oil resistant jacket and weather resistant. Also is water 
resistant. 600V 

Spacing - The distance between the centers of two adjacent conductors. Pitch. 

Spark Test - a test that is designed to locate imperfections (usually pin-holes) in the 
insulating of a wire or cable by application of a voltage for a very short period of time 
while the wire is being drawn through the electrode field 

Specific Gravity - the ratio of the density (mass per unit volume) of a material to that of 
water. 

Specific Inductive Gravity (S.I.C) -same as dielectric constant. 



Spiral Wrap -the helical wrap of a material over a core. 

ST - hard service cord, jacketed, same as type S except all-plastic construction, 600V, 
60C to 105C. 

STOO - same as STO but with oil-resistant thermoplastic outer jacket. 600V, 60C. 

-service cord with oil resistant Thermoplastic jacket and weather resistant. STOW-A 
meets CSA approval for outdoor use. Can be water resistant -UL 600V 

-service cord with Thermoplastic, and weather resistant jacket, but no oil resistant. Can 
me UL water resistant. STW-A meets CSA approval for out door use 600V 

Stability Factor - the difference between the percentage power factor at 8-colts/mil 
and at 40 volts/mil measured on wire immersed in water at 75C for a specified time. 

Stranding Wave - the stationary pattern of waves produced by two waves of the same 
frequency traveling in opposite directions on the same transition line. The existence of 
voltage and current maxima and minima along a transmission line is a result of reflected 
energy for an impedance mismatch 

Standing Wave Ratio - a ratio of the maximum amplitude to the minimum amplitude of 
a standing wave stated in current or voltage amplitude 

Static Condition - used to denote the environmental conditions of an installed cable 
rather than the conditions existing during LAN installation. 

Strand -a single un-insulated wire. 

Stranded Conductor - a conductor composed of individual groups of wires twisted 
together to form an entire unit. 

Strip Force -the force required o remove a small section of insulating materials from 
the conductor it covers. 

Suggested Working Voltage - AC voltage that can be applied between adjacent 
conductors. 



Surface Resistively - the resistance of a material between two opposite sides of a unit 

square of its surface. It is usually expressed in ohms. 
Surge - A temporary and relatively large increase in the voltage or current in an electric 
circuit or cable. Also called transient 

Surlyn - DuPont's trade name for their thermoplastic resin with ionic crosslink's 

Sweep Test -Testing a characteristic of a cable or device across a range of 
frequencies. In cable, it usually implies return loss or structural return loss (see also). 
Switchboard Cable -a cable used within and between the central office main frames 

and the switchboard. 
…………………………………………………………………………………………………… 



[T] 
Take-Up - the process of accumulating wire or cable into a reel, bobbin, or some other 
type of pack. Also, the devise for pulling wire or cable through a piece of equipment or 
machine 

Tank Test - a voltage dielectric test in which the test sample is submerged in water and 
voltage is applied between the conductor and water as ground 

Tape Wrap - a spirally applied tape over an insulated or non-insulated wire 

TC - Tray cable. Article 340 NEC. 

Tear Strength - the force required to initiate or continue a tear in a material under 
specified conditions. 

Teflon -DuPont Company trademark for fluorocarbon resins. (FEP -Fluorinated 

and chemical and heat resistance.). (TFE - Tetrafluoroethylene. A thermoplastic 
material with good electrical insulating properties and chemical and heat resistance.). It 

ethylene-propylene. A thermo-plastic material with good electrical insulating properties 

is not suitable where subjected to nuclear radiation and does not have good high 
voltage characteristics. FEP Teflon is extrudable in a manner similar to PVC and 
polyethylene. This means that long wire and cable lengths are available. TFE Teflon is 
extrudable in a hydraulic ram type process. Lengths are limited due to amount of 
material in the ram, thickness of the insulation, and preform size. TFE must be extruded 
over a silver- or nickel-coated wire. The cost of Teflon is approximately 8 to 10 times 
more per pound than PVC compounds. 

Tefzel - Fluorocopolymer thermoplastic material has excellent electrical properties, heat 
resistance, chemical resistance, toughness, radiation resistance, and flame resistance. 

Telemetry Cable -cable used for transmission of information from instruments to the 
peripheral recording equipment 

Temperature Rating -The temperature range in which a material will perform its 
function without undue degradation. 

Tensile Strength -the pull stress required to break a given specimen. 



Tension Member -a member included on a fiber cable to add tensile strength 

Terminals - metal wire termination devices designed to handle one or more conductors, 
and to be attached to a board, bus, or block with mechanical fasteners or clipped on. 

Teat Lead - a flexible, insulated lead wire used for making tests, connecting instruments 
to a circuit temporarily, or for making temporary electrical connections. 

TEW -Canadian Standards Association type appliance wires. Solid or stranded single 
conductor, plastic-insulated 600V, 105C 

Textile Braid -any braid made from threads of cotton, silk, or synthetic fibers. 

TFFN -fixture wire, thermoplastic-covered solid or 7 strands with nylon sheath. 60C 

Thermal Aging -exposure to a thermal condition of programmed series of conditions 
for pre-described periods of time 

Thermal Rating - the maximum and/or minimum temperature at which a material will 
perform its function without undue degradation. 

Thermal Shock -a test to determine the ability of a material to withstand heat and cold 
by subjecting it to rapid and wide changes in temperature 

Thermocouple -a device consisting of two dissimilar metals in physical contact, which 
when heated will develop an emf output 

Thermocouple Element - a thermocouple designed to be used as part of an assembly, 
but without associated parts such as the terminal block, connecting head, or protection 
tube. 

Thermocouple Extension Cable - a cable comprised of one or more twisted 
thermocouple extention wires under a common sheath. 

Thermocouple Extension Wire -a pair of wires of dissimilar alloys having such emf-
temperature characteristics complementing the thermocouple which is intended to be 
used, such that when properly connected allows the emf to be faithfully transmitted to 
the reference point. 



Thermocouple Wire (Grade) -a pair of wires of dissimilar alloys having emf-
temperature characteristics calibrated to high temperature levels than the extension 
type of thermocouple wires 

Thermoplastic -A material which will soften, flow, or distort appreciably when 
subjected to sufficient heat and pressure. Examples are polyvinyl chloride and 
polyethylene. 

Thermostat -a material which hardens or sets by heat, chemical or radiation 
crosslinking techniques and which, once set, cannot be re-softened by heating. 

THHN -90C, 600 volt, nylon jacketed building wire for dry locations. 
THW -thermoplastic vinyl insulated building wire. Flame-retardant, moisture and heat 
resistant. 75C Dry and wet locations. 


THWN -same as THW but with nylon jacket overall. 75C 
Tin Overcoat (TOC) -tinned copper wire, stranded, then coated with pure tin. 
Tinned Copper - tin coasting added to copper to aid in soldering and inhibit corrosion. 
Topcoat - bare (untinned) copper wire, stranded, then coated with pure tin. 
Tracer - a means of identifying polarity. 
Transfer Impedance - for a specified cable length, transfer impendence is defined as 


the ratio of internal longitude in a voltage to external current flow on the cable shield. 
Transfer impendence is used to determine shield effectiveness against both the ingree 
and egress of interfering signals. 

Transmission - transfer of electric energy from one location to another through 

conductors or by radiation or induction fields. 
Transmission Line - An arrangement of two or more conductors, a coaxial cable, or a 
waveguide used to transfer signal energy from one location to another. 


Transmission Loss - the decrease or loss in power during transmission of energy from 
one point to another. Usually expressed in decibels. 



Tray -a cable tray is a unit or assembly of units or sections, and associated fittings, 
made of noncombustible materials forming a rigid structural system used to support 
cables. 

Tray Cable -a factory-assembled muticonductor or multipair control, signal or power 
cable specifically approved under the National Electric Code for installation in trays 

Triaxial Cable -A cable construction having a conductor, and two isolated braid 
shields, all insulated from each other. A coaxial cable with a second braid applied over 
an inner jacket and an outer jacket applied over the outer braid. Commonly used in 
television camera systems. 

Triboelectric Noise -Noise generated in a shielded cable due to variations in 
capacitance between the shield and conductors as the cable is flexed. 

Triple (Triad) -a cable consisting of three insulated single conductor cables twisted 
together. 

Triplex - a cable composed of three insulated single conductor cables twisted together. 

Twin Cable -a cable composed of two separately insulated stranded conductors laid 
parallel or twisted together. 

Twin Coaxial Cable -a single cable consisting of two separate coaxial cables laid 
adjacent and parallel or twisted together. 

Twin Line -a transmission line which has a solid insulating material, in which the two 
conductors are placed in parallel to each other. 

Twinner - a device for twisting together two conductors. 

Twisted Pair - Two lengths of insulated conductors twisted together. The traditional 
method for connecting home and many business computers to the telephone company. 
Gets its name because two insulated copper wires are twisted together, both of which 
are needed for each connection. In commercial environments, performance of data 
transmission can be improved by adding a composite tape to the wire. This is known as 
shielded twisted pair. 

Twisted Triad - any three individually insulated conductors which are twisted together 



[U] 
UHF -abbreviation for ultra high frequency, 300 to 3,000 Mhz. 

UL - Underwriters Laboratories. A nonprofit organization which tests and verifies 
construction and performance of electronic parts and equipment, including wire and 
cable. 

Unbalanced Circuit -a transmission line in which voltages on the two conductors are 
unequal with respect to ground; e.g., a coaxial cable 

Unidirectional Concentric Stranding -a stranding where each successive layer has a 
different lay length, thereby retaining a circular from without migration of strands from 
one layer to another 

Unilay -more than one layer of helically laid wires with the direction of lay and length of 
lay the same for all layers.

…………………………………………………………………………………………………….. 



[V] 
Valley -any void between the insulated conductors of cable or between a cable core 
and it's covering. See also interstice 

Velocity of Propagation -The transmission speed of electrical energy in a length of 
cable compared to speed of light in free space. Usually expressed as a percentage. 

VHF -Very High Frequency. International Telecommunication Union designation for the 
30-300 MHz band of frequencies. 

Video Pair Cable -a transmission cable containing low-loss pairs with impedance of 
125 ohms. Used for TV pick ups, closed circuit TV, telephone carrier circuits, etc 

Volt -A unit of electromotive force. 

Voltage - Electrical potential of electromotive force expressed in volts. 

Voltage Levels -power-limited 0-300 volts, low voltage 600-2000 volts, medium 
voltage 5000-69000 volts. 

Voltage Rating - The highest voltage that may be continuously applied to a cable 
construction in conformance with standards or specifications 

Voltage Stranding Wave Radio (VSWR) - the ratio of the maximum effective voltage to 
the minimum effective voltage measured along the length of miss-matched radio 
frequency transmission line. 

Volume Resistively (Specific Insulation Resistance) -the electrical resistance 
between opposite faces of a 1 cm. cube of insulating material, commonly expressed in 
ohms/centimeter. 

Vulcanization - an irreversible process during which a rubber or polymeric compound 
through a change in its chemical structure (for example, crosslinking) become 
thermoset. 

VW-1 - A flammability rating established by Underwriters Laboratories for wires and 
cables that pass a specially designed vertical flame test, formerly designed FR-1. 



[W] 
Wall Thickness -The thickness of an insulation or jacket. 
Water Absorption - water by percent weight absorbed by a material after a given 
immersion period. 

Water Blocked Cable -a cable constructed with no internal voids in order to allow no 
longitudinal water passage under given pressure. 
Watt - A unit of electrical power. 
Wavelength - The distance between positive peaks of a signal. As the frequency 


increases, and waves get closer together, the wavelength decreases. 
Wicking - the longitudinal flow of a liquid in a wire or cable due to capillary action. 
Wire -a single conductor, typically with a covering of insulating. 
Wire Gauge - a measure of the diameter or size of wires. The sizes are expressed by 


numbers. 
Working Voltage - see voltage rating 
……………………………………………………………………………………………………… 




[X] 
XHHW -high temperature (90C) chemically cross-linked polyethylene jacketed small 
diameter building wire. 
XLP -Cross-linked polyethylene 
…………………………………………………………………………………………………… 


[Y] 
Yield Strength - the minimum stress at which a material will start to physically deform 
without further increase in load. 
…………………………………………………………………………………………………… 


[Z] 
Z-Symbol for impedance 
ZW -NEC conductor type designation for conductors with ETFE insulating for use in 
wet or dry locations 

 

Booking.com

 

Home Up Next

Best Hotel Reservation

In Saudi Arabia & World Wide

Saudi Arabia
 Alrashid Cyber Mall, member of The Saudi Network, Trade and business informations and links to Saudi arabia, arabian gulf and middle east area.
Shopping in Saudi Arabia

Send E-mail to TSN@The-Saudi.Net with questions or comments about The Saudi Network.
1001 Arabian Network, Alrashid Cyber Mall and The Saudi Network are members of Nova* Stars* Information Services
The Saudi Network, Trade and business information and links to
Saudi Arabia, Arabian Gulf and Middle East Area.

morocco, libya, lebanon, kuwait, jordan, iraq, egypt, bahrain, algeria, yemen, uae, tunisia, syria, sudan, qatar, palestine, oman

We are Looking for Business Sponsorship or Marketing Partnership